Jacking beams

Jema Autolifte is a major supplier of jacking beams to the Danish and international market. There are several different jacking beams, both for your 4 post car lifts, but also a workshop jack that is used e.g. for wheel change or smaller repairs. At Jema Autolifte, we offer several different jacking beams for your 4 post car lifts, depending on which car lift you choose and depending on what needs your jacking beam should cover.

Sort by:
Show:

Jacking beam suspension Euro Line JA2000J-E - (62.289.00)

Jacking beam suspension Euro Line JA2000J-E 
✔ Made in Denmark
✔ Best quality possible
✔ Suspension for JA2000J-E

£119.98

Jacking beam Basic line - Oil hydraulic (JA1600J-OIL)

Basic line - The affordable choice Jacking beam for JA4000FP Manual safety locks Easy and solid operation Max lifting capacity 1.6T
✔ Lifting height up to 38 cm
✔ Lifting capacity 1.6T
✔ Easy and solid operation

£519.00

Jacking beam Basic line - Air hydraulic (JA1600J-AIR)

Basic line - The affordable choice Good function Manual safety lock Easy and solid operation Max. lift 1.6T
✔ Lifting height up to 38 cm
✔ Lifting capacity 1.6T
✔ Easy and solid operation

£574.00

Jacking beam suspension Euro line - JA8000J-E (58.750.10)

Suspension for Euro Line jacking beam JA8000J-E
✔ Made in Denmark
✔ Best quality possible
✔ Suspension for JA8000J-E

£689.00

Jacking beam Basic line - Air hydraulic (JA2000J-AIR)

Basic line - Danish designed jacking beam Fantastic Danish design Safety in the forefront Easy and solid operation CE approved
✔ Fantastic Danish design
✔ Lifting height up to 45 cm
✔ Lifting capacity 2T

£689.00

Jacking beam Euro line - Hydraulic (JA2000J-E)

Euro line - Danish produced jack Fantastic Danish quality Great lifting height Easy and solid operation CE approved
✔ Made in Denmark
✔ Lifting height up to 40 cm
✔ Lifting capacity 2T

£1,430.00

Jacking beam Euro line - Hydraulic (JA8000J-E)

Euro line - Danish produced jacking beam Fantastic Danish quality "Heavy duty" jacking beam Easy and solid operation CE approved
✔ Danish design
✔ Lifting height 14,1 cm
✔ Lifting capacity 8T

£4,798.00
Show:

 

Jacking beam for 4 post car lift

When you must choose which jacking beam to buy for your 4-post car lift, it is important to choose the right jacking beam which suits the work you perform at your car workshop. For our 4-post car "parking" lift JA3500F we have two different models, one jacking beam JA1600J-OIL is a jacking beam that is controlled by the engine of your 4-post car lift JA3500F, ie. there is a 3-way valve that can be adjusted depending on whether it is the lift that needs to lift, or it is the jacking beam. If the handle is in position to lift the jacking beam, you as a user must place the jacking beam's lifting platforms under the car's lifting points, and at the same time place the rubber blocks in the same place, when this is done, you as a user can press the "UP" button on the lift control box. the jacking beam starts to lift, however, as with all other lifting tools, it is important to ensure that the car is lifted safely on the jacking beam, so check when the rubber blocks hit the car's lifting points that it is lifted properly. Then you can safely lift the car to the desired height, so that the car's wheels come free of your 4-post car lift runways. While the jacking beam is lifting, the jack's safety lock automatically engages, so should a hose break, the jacking beam will not fall. When the work is done and you want to lower the car again, then the safety lock must be released and then you can press the "DOWN" button on the lift control box and the jacking beam will lower to the bottom position. The jacking beam JA1600J-OIL is a jacking beam Jema Autolifte has sold for many years, and therefore it is 100% thoroughly tested and since Jema Autolifte goes up in your safety, you can safely buy and use this jacking beam. The other model jacking beam that fits our 4-post "parking" lift JA3500F and which is also often used as the No. 2 jacking beam on our two basic line 4-post car lift models is the jack JA1600J-AIR. The jacking beam JA1600J-AIR has the same design as the previously mentioned jacking beam JA1600J-OIL, but the jacking beam JA1600J-AIR has an air hydraulic pump located on the front of the jacking beam. When you as a user must lift the car, you can stand under the car, place the jacking beams lifting platforms under the car lifting points and at the same time place the rubber blocks correctly, when that is done, press the pump pedal and the jacking beam will start rising, remember to check the car is placed safely on the jacking beam, and then lower the jack into the safety lock. When the work with the car is finished, rise the jacking beam up so that it releases from the safety lock, and then release the safety lock, and press the pedal so that the jacking beam lowers easily and safely until it is in the bottom position. Both jacking beams JA1600J-OIL and JA1600J-AIR have a lifting capacity of 1.6T and a maximum lifting height of 380mm.

 

Basic line jacking beam JA2000J-AIR

The jacking beam JA2000J-AIR is a 2T jacking beam that has an extremely wide lifting width, Max / Min. width: 910-1610mm, so the jacking beam can lift most cars. The jacking beam JA2000J-AIR is a fantastic jacking beam. The jacking beam is placed between the lanes on the lift and will then be placed under the car as needed. Once the jacking beam is placed and the lifting platforms are located below the car's lifting points, the jacking beam is lifted via the air hydraulic pump located on the front of the jacking beam. When you as a user press the hand pedal, the jacking beam lifts, and the car's wheels will lift from the runways, when the jacking beam lifts, the jack's safety lock automatically engages and therefore ensures you as a user that safety is in order. When the work with the car is finished, lift the jacking beam up so that it releases from the safety lock, and then release the safety lock on the locking handle, and press the pedal so that the jacking beam lowers easily and safely until it is in the bottom position. Jema Autolifte goes up to your safety therefore the jack automatically goes into safety lock when you lift the car!

 

Euro line jacking beams

In our Euro line series, Jema Autolifte has 2 different jacking beams depending on which lifting capacity and which 4-post car lift is to be used for. Our jacking beam JA2000J-E is a Danish produced jacking beam that fits on our Euro line 4-post car lifts JA5000F-E and JA5001F-E, the jacking beam is simply in a fantastic quality that cannot be improved. The jacking beam JA2000J-E has a lifting capacity of 2T and a Max. lifting height of 400mm. The jacking beam is operated via 2 handles on the jacking beam, one handle is for lifting the jacking beam and the other handle is for operating the safety lock on the jacking beam. When the jack needs to be lifted, you as a user stand under the car, and place the jacking beam's lifting platforms under the car's lifting points, when this work is done, turn the handle on the jacking beam and the air hydraulic pump starts pumping so that the jacking beam rises, the jacking beam goes automatically in the safety lock and lift the car's wheels from the runway, when you reach the desired height you can lower the jacking beam so that the safety lock goes into intervention. When the work on the car is done, the jacking beam is lifted slightly so that the safety lock goes free, turn the handle and trigger the safety lock, then and turn the lowering handle so that the jacking beam begins to lower easily and safely until it is in the bottom position. Jema AutoLifte is think about your safety therefore, the jacking beam automatically goes into safety lock when you lift the car!

 

For our large 4-post “Heavy-duty” car lift, JA12000F-E we have our Heavy-Duty jacking beam JA8000J-E, which has a lifting capacity of 8T and a max. Lifting height of: 1410mm. JA8000J-E has 2 lifting platforms that will surely lift your car and of course there are safety locks that ensure the jack cannot lower while you work on the car. As on the "little brother", the jacking beam is controlled by 2 handles on the front of the jacking beam.

 

Workshop jacks for all kinds of work

Jema AutoLifte can also offer our fantastic customers 2 models workshop service jacks. Both models have a great price of £154,98 + VAT. The workshop jack JA1012SJ is a 3.25t jack that has a min. Height of 98 mm and a max. Lifting height of 535 mm. The jack is a good and solid workshop power. Our other model workshop power JA1013SJ is a good aluminum jack with a lifting capacity of 2T, and a min. Height: 90mm and a max. Lifting height of 445mm. Jema Autolifte goes up in your safety So, of course, all our jack is CE approved in relation to the European rules.

If you have any questions about our jack, you are of course welcome to contact one of our consultants on tel. +45 48180300.